PD300-BB | Laser Photodiode Sensors | Power Sensors - Ophir

PD300-BB

7Z02405
Description: 

The PD300-BB radiometric sensor with swivel mount has a flat spectral response photdiode sensor for measuring broadband light sources. It covers the spectral range 430 - 1000nm and has a 10x10mm aperture. Its power measuring range is 50pW - 4mW. The 50mW version measures from 50pW to 50mW. The sensor comes with a 1.5 meter cable for connecting to a meter or PC interface.

Specification

  • 10x10mm
  • 430-1000nm
  • 50pW-4mW
  • 118 L x 10 W x 18 D (mm)
  • 1μJ
  • 10W/cm²
  • 0.2 s
  • 4mW
  • CE, UKCA, China RoHS
Need help finding the right sensor? Try our Sensor Finder

FAQ

I am using a PD300 type sensor. I have a broadband light source, but only want to measure the power of a specific wavelength. Can I set my meter to that wavelength and get a measurement?

The PD300 series of photodiode-based sensors are calibrated with a full spectral curve using a scanning monochromator (plus a few laser "anchor points").

 

The wavelength ("Laser") setting tells the meter what wavelength is being used and hence what calibration factor to apply when a measurement is underway. It does not, however, physically limit the possibility of other wavelengths from entering. All light (within the sensor's specified range of course) entering the detector will be measured; the meter will apply the calibration factor meant for the selected wavelength, "thinking" that only that wavelength is present.

 

In other words, these sensors assume a monochromatic light source. Their relative spectral response is not flat and they are therefore not suited for broadband beams.

 

So, if you want to check one wavelength from a broadband source, you will need to use a wavelength filter that only passes that wavelength. Then you should set your meter to the appropriate wavelength to account for the detector's relative sensitivity.

Was this FAQ helpful to you? yes no
Close

Do I need to recalibrate my instrument? How often must it be recalibrated?

Unless otherwise indicated, Ophir sensors and meters should be recalibrated within 18 months after initial purchase, and then once a year after that.

Was this FAQ helpful to you? yes no
Close

Calibration

 

Videos

FAQ: Photodiode Sensors for measuring very low laser powers FAQ: Photodiode Sensors for measuring very low laser powers
How to measure power of very low power pulsed laser beams How to measure power of very low power pulsed laser beams How to measure power of very low power pulsed laser beams

When using a photodiode laser power sensor to measure very low power pulsed beams (nW to mW), there are some issues you need to be aware of. This video shows you how to avoid some common problems and ensure maximum accuracy.

How do I measure power of broadband sources like flash lamps, some LEDs, or sunlight? How do I measure power of broadband sources like flash lamps, some LEDs, or sunlight? How do I measure power of broadband sources like flash lamps, some LEDs, or sunlight?

This video explains how to use Ophir sensors and meters to measure the power or energy of broadband light sources such as solar radiation, flash lamps, LEDs etc.

Photodiode Sensors for Measuring Very Low Powers Photodiode Sensors for Measuring Very Low Powers Photodiode Sensors for Measuring Very Low Powers

In this short "Basics" video, we review in general the use of photodiode sensors for measuring very low laser powers.

In this short “Basics” video, we review in general the use of photodiode sensors for measuring very low laser powers.

Tutorials

Tutorials and Articles

Laser Power Sensors introduction

As described in the general introduction, the thermopile sensor has a series of bimetallic junctions. A temperature difference between any two junctions causes a voltage to be formed between the two junctions. Since the junctions are in series and the «hot» junctions are always on the inner, hotter side, and the «cold» junctions are on the outer, cooler side, radial heat flow on the disc causes a voltage proportional to the power input. Laser power impinges on the center of the thermopile sensor disk (on the reverse side of the thermopile), flows radially and is cooled on the periphery. The array of thermocouples measures the temperature gradient, which is proportional to the incident or absorbed power. In principle, the reading is not dependent on the ambient temperature since only the temperature difference affects the voltage generated and the voltage difference depends only on the heat flow, not on the ambient temperature.

 Read more...

Common Reasons for Photodiode Sensor Damage or Out of Tolerance Conditions

We have included this document with your recent calibration order because we have noticed an out of tolerance condition obtained from your equipment when returned for calibration. This document was created to assist our valued customers in the proper care and maintenance of Ophir photodiode sensors. The following information is for reference only. If you have any reason to believe that the sensor is no longer performing within the original specifications, we always recommend that you send it in for repair and/or recalibration by our trained technicians to bring the unit back to the proper NIST traceable standards.

Ophir photodiode sensors can be used for many years without any repairs when used with the proper laser optical setup. Many of our customers have sensors that are using their original absorber that are over ten years of age. We hope that this document will enable you to also enjoy the long life and reliable results that Ophir- Spiricon is known for.

 Read more...

How to Properly Select a Laser Power or Energy Sensor

The selection of a sensor to accurately measure the power of a laser or energy of a pulsed laser can seem like a simple and easy procedure. However, many times the selection process is limited to choosing a sensor that only meets the range of power or energy to be measured, leaving out several other essential criteria of the laser specifications; that without their consideration, can allow the wrong sensor to be selected, the laser to be measured inaccurately and likely to cause the sensor to fail prematurely.

Watch Our Laser Measurement Video

 Read more...

Effect of Ambient Conditions on Laser Measurements

We are often asked about the specified ranges of various ambient conditions (temperature, humidity, etc.) for Ophir instruments. In this article we will clarify the effects of these conditions on laser measurements, so you’ll be able to use your Ophir laser measurement instrument effectively.

 Read more...

Ophir Power/Energy Meter Calibration Procedure and Traceability/Error Analysis

This document discusses the interpretation and basis for stated measurement accuracy of Ophir Laser Power/Energy meters.
1. General Discussion
2. Combination of Errors and Total Error
3. Analysis of Power and Energy Calibration Errors
4. Detailed Analysis of Power and Energy Calibration Errors

 Read more...

Laser Measurements in Materials Processing: How and When They Absolutely, Positively Must Be Made

19th century British physicist and engineer William Thomson, 1st Baron Kelvin, was the first to say, “If you can’t measure it, you can’t improve it.” When applying this principle to improving laser-based processes, there are a variety of parameters that must be measured. Given the continuously rising power of laser systems in material processing, the requirements for measurement systems are more challenging than ever. Which technologies are available to measure high-power lasers? How often should they be measured? What measurements should be tracked? When this data is collected, what should be done with it? Read more...

5 Situations Where Laser Performance Measurement is Necessary

Measuring the performance of a laser has possible for a number of years and is accomplished with a variety of techniques. These electronic laser measurement solutions give the laser user more relevant, time-based data that shows trends in laser performance rather than single data points. While these solutions have provided laser users with the ability to present data in a simple and easy to understand manner, the application of the data still seems to be unclear to many laser users. Read more...

Accessories

Customers that purchase the above items also consider the following items. Ophir-Spiricon meters and sensors include a standard manufacturers warranty for one year. Add a one year Extended Warranty to your meter or sensor, which includes one recalibration.
  • PD300 CDRH

    PD300-CDRH-7mm

    7Z02418

    Ø7mm aperture CDRH adapter for PD300 series.
    (Dimensions: 42 L x 21.4 W x 12.5 D (mm))

  • PD300-CDRH-3.5mm

    PD300-CDRH-3.5mm

    7Z08336

    Ø3.5mm aperture CDRH adapter for PD300 series
    (Dimensions: 42 L x 21.4 W x 12.5 D (mm))

  • Cable

    5m Cable

    7E01125A

    * Order only with purchase of a sensor.
    5m cable to connect sensor to power meter or interface. Order along with sensor to receive this instead of the standard 1.5m cable.

  • 10m cable

    10m Cable

    7E01125B

    * Order only with purchase of a sensor.
    10m cable to connect sensor to power meter or interface. Order along with sensor to receive this instead of the standard 1.5m cable.