FPD-UV-3000 — это быстродействующий оптический детектор, позволяющий визуализировать и измерять временные характеристики лазерных пучков в спектральном диапазоне от 193 до 1100 нм. Он оснащен кремниевым PIN-фотодиодом с повышенной чувствительностью к УФ-излучению и предназначен для преобразования оптических сигналов в электрические, которые впоследствии измеряются приборами сторонних производителей, такими как осциллографы и анализаторы спектра. Время нагнетания для детектора FPD-UV-3000 составляет 3 наносекунды. Его напряжение обратного смещения обеспечивается внешним источником питания постоянного тока (входит в комплект поставки).
- UV-Silicon photodiode for 193-1100 nm spectral range
- Fast 3.0 ns response time
- 2.55 mm diameter active area
- Optional attenuators and fiber optic adapters Показать все функции
Характеристики
- Product NameFPD-UV-3000(a)
- Sensor TypeUV-Silicon
- Rise Time/Fall Time3 ns
- Spectral Range193-1100 nm
- Active Area Diameter2.55 mm
- Noise Equivalent Power<0.10 pW/√Hz
- Detector Area5.11 mm²
- Wavelength of Peak Sensitivity890 nm
- Responsivity at Peak Wavelength0.58 A/W
- Responsivity (Irradiance) at Peak Wavelength1.5 V/(W/cm²)
- Bias Voltage24 VDC
- Bias Voltage SourceExternal
- Bandwidth118 MHz
- Dark Current<10 nA
- Maximum Average Power15 mW
- Mounting (Tapped Holes)8-32 & M4
- Output ConnectorBNC
- Accessory ThreadM20x1
- Dimensions54 x 34 x 40 mm (LxWxD)
- CE ComplianceYes
- UKCA ComplianceYes
- China RoHS ComplianceYes
Функции
Pulse Characterization Sensor Overview
Using these Ophir fast photodetectors, you can see and measure the temporal characteristics of pulsed and CW laser beams.
How to Use Pulse Characterization Sensors with High Power Beams
Pulse Characterization Sensors help you see and measure the temporal characteristics of pulsed laser beams – pulse duration and temporal shape....
Fast Photodiode Spectral Responsivity
Responsivity is defined as the produced photocurrent (in Amperes) per Watt of incident radiation. It is a function of wavelength. Hence, the spectral response of the photodiode should be as high as possible at the wavelength of the laser to be measured. The spectral responsivities of the FPD series are shown in the figure. Ophir offers several fast photodiodes models with Silicon photodiodes having spectral response from 320 nm to 1100 nm, UV enhanced Silicon with extended response from 193 nm to 1100 nm, and InGaAs photodiodes which are sensitive from 900 nm to 1700 nm.
Часто задаваемые вопросы
- Do I need to recalibrate my instrument?Ответ
Ophir's temporal sensors do not require calibration.
- What kind of measurements can I do with a temporal detector? Why are they important?Ответ
With a temporal detector you can measure the rise time, fall time, pulse duration and pulse frequency. Many laser applications use pulsed laser, for example medical lasers, LIDARs, and high power fiber laser for metal processing to name a few. The parameters of the laser pulses are critical for the performance of the application.
- The temporal sensor can provide accurate measurement of temporal parameters. How can I relate those to absolute value of pulse energy?Ответ
Pulse energy can be measured directly using one of Ophir's calibrated energy sensors. Another way is to use a calibrated power sensor and calculate the pulse energy using:
Pulse energy [J] = average power [W] / pulse rate [pulses per second]
Temporal sensors provide a signal that is proportional to the instantaneous power output of the laser. When viewing the pulse waveform on an oscilloscope, the integrated area under the curve is proportional to the total pulse energy.
- I need to measure the temporal pulse shape of a very powerful laser. How can I do that without damaging the detector?Ответ
There are several possible ways to do this:
- Use a beam sampling optic (partially reflective mirror or uncoated window).
- Feed the laser beam into an integrating sphere and attach the temporal detector to the sphere using the adapter accessory.
- Use a beam dump and position the detector such that it picks up some of the reflected laser radiation.
Attenuating accessories are available (see temporal detector's product page). Laser power density on the attenuators should be less than 50 W/cm².
- What is the difference between calibrated power sensors such as PD300 and temporal sensors?Ответ
Calibrated power sensorsmeasure the average power of CW and pulsed laser beams. The sensor is connected to an Ophir Meter or PC Interface. Power sensors are optimized for low noise and linear response in order to maximize power measurement accuracy. The measured laser beam must be smaller than the sensor's aperture in order to obtain an accurate power measurement. Temporal sensors are optimized for high speed response in order to reproduce pulse temporal characteristics with high fidelity. A temporal sensor is usually smaller than the laser beam size and samples a portion of the beam. The temporal sensor is connected to a scope or spectrum analyzer to display temporal characteristics of pulsed lasers.
- I don’t see my signal on the oscilloscope or the signal is not as expected. What should I do?Ответ
See the troubleshooting section of the user manual in the temporal detector's product page for detailed information.
- I sometimes need to see an analog representation of my laser power on a scope, in parallel to measuring it with a thermal sensor. What solutions are available?Ответ
There are a number of options, depending on the purpose.
- In many cases, the simplest solution could be to make use of the analog output of the meter – that gives a voltage signal proportional to the actual reading (it is in fact just a D/A translation of what is being displayed), so it represents a fully calibrated reading. The full scale value is a function of the meter being used and the power range it is on.
- The "SH to BNC connector" (Ophir P/N
) simply takes the raw output from the detector element and sends it to the scope. It bypasses the sensor's EEROM which contains the calibration data, so it essentially turns the sensor into an uncalibrated "dumb" analog sensor. It should be noted, though, that in some cases we could be talking about a signal to the scope that may be low, perhaps even near the noise level of the scope, which limits the usefulness of this method at low powers. - If the need is to see the pulse width – the temporal profile – the solution (assuming applicable specs) is to use an appropriate temporal sensor connected to a scope. You can point it anywhere where it will catch some backscatter from your laser, and you'll see the pulse temporal form as it really is.
- In the specifications of the “Pulse Characterization Sensors”, Noise Equivalent Power is specified in units of “√Hz”. What does that mean”?Ответ
Admittedly a unit such as “√ Hz” is not very intuitive. In general: Noise Equivalent Power (NEP) is defined as the signal power that gives a signal-to-noise ratio of 1 in a one-hertz output bandwidth. Taking the bandwidth of the measurement into account is where the “square root of Hz” comes in. The noise spectrum typically has a relatively flat response, and the noise level changes with the square root of the frequency range. For example, if the frequency range doubles, the noise component increases by √2 (1.414). In detector datasheets, the bandwidth is typically normalized to 1 Hz (which is usually far below the detection bandwidth), to allow detectors with different bandwidth specifications to be directly compared.
Аксессуары
Attenuators
FPD to IS6 Adapter
For mounting FPD sensor series (except FPS-1) to North Pole post of IS6 series.
| Compare | Description | Drawings, CAD & Specs | Avail. | Price | ||
|---|---|---|---|---|---|---|
![]() | 7Z08350FPD (except FPS-1) to IS6 adapterFPD Sensor Adapter, IS6 Integrating Sphere, North Pole Port, Matte Black Coated |
Fiber Connector Adapters
These adapters allow for power measurement of connectorized fiber-optic cables. The sensor may need an additional mounting bracket to connect to these fiber adapters.
| Compare | Description | Drawings, CAD & Specs | Avail. | Price | ||
|---|---|---|---|---|---|---|
![]() | 7Z08227SC Fiber Connector Adapter, Power and Energy Sensors | |||||
![]() | 7Z08226ST Fiber Connector Adapter, Power and Energy Sensors | |||||
![]() | 7Z08229FC Fiber Connector Adapter, Power and Energy Sensors | |||||
![]() | 1G01236ASMA Fiber Connector Adapter, Power and Energy Sensors |
Extended Warranty for Sensor
Customers that purchase the above items also consider the following items. Ophir-Spiricon meters and sensors include a standard manufacturers warranty for one year. Add a one year Extended Warranty to your meter or sensor, which includes one recalibration.
| Compare | Description | Drawings, CAD & Specs | Avail. | Price | ||
|---|---|---|---|---|---|---|
![]() | XWAR-SENSORExtended Warranty for Sensor |
Ресурсы
Data Sheets
Fast Photodiode Detectors (FPD) Datasheet(448.2 kB, PDF)
Drawings & CAD
FPD-UV-3000/FPD-UV-3000-JP Drawing(194.1 kB, PDF)
Manuals
FPD-IG-175/FPD-UV-3000/FPD-UV-3000-JP/FPD-VIS-300 User Manual(598.3 kB, PDF) FPD-UV-3000 Quick Reference(60.2 kB, PDF) FPD-UV-3000-JP User Notes(PDF)
Catalogs
Pulse Characterization Sensors Catalog(2.6 MB, PDF) Laser Power & Energy Measurement and Laser Beam Analysis Catalog(27.5 MB, PDF)
Technical Articles
Pulsed Lasers: How to Choose the Right Fast Photodetector Ophir Power/Energy Meter Calibration Procedure and Traceability/Error Analysis Laser Measurements in Materials Processing
















