资源 & 下载
Data Sheets
Pyroelectric Energy Sensors 8µJ to 10J Datasheet(381.3 kB, PDF) Absorption and Damage Graph(220.6 kB, PDF) Wavelength and Repetition Rate Chart(178.6 kB, PDF)
3D 产品模型
Drawings & CAD
PE25-C & PE25BF-C Drawing(125 kB, PDF)
Catalogs
Energy Sensors Catalog(4.6 MB, PDF) Laser Power & Energy Measurement and Laser Beam Analysis Catalog(27.5 MB, PDF)
Technical Notes
5 Situations Where Laser Performance Measurement is Necessary Effect of Ambient Conditions on Laser Measurements Oscilloscope Adapter for Ophir Pyroelectric Sensors Can Ophir pyroelectric sensors measure single shot energy or energy at very low repetition rates? How to Properly Select a Laser Power or Energy Sensor
Technical Articles
Ophir Power/Energy Meter Calibration Procedure and Traceability/Error Analysis Laser Measurements in Materials Processing
Tutorials
相关产品
Heat Sink
Screws onto rear of PE-C series sensors allowing working at over 50% higher average powers
| 对比 | 型号 | 图纸、CAD和参数 | 库存 | 价格 | ||
|---|---|---|---|---|---|---|
 | 7Z08267Heat Sink, PE25-C and PE50-C Series | 有库存 |
Fiber Connector Adapters
These adapters allow for power measurement of connectorized fiber-optic cables. The sensor may need an additional mounting bracket to connect to these fiber adapters.
Fiber Adapter Mounting Bracket
A mounting bracket is needed to connect most power and energy sensors to a fiber adapter (SC, ST, FC or SMA). This bracket can be used for pyroelectric energy sensors in the PE9, PE10 and PE25 series. It is not compatible with diffuser-equipped sensors.
Nova PE-C Adapter
The adapter plugs between the Nova D15 socket and the smart plug of the PE-C and PD-C sensors to allow the Nova to operate with these sensors.
| 对比 | 型号 | 图纸、CAD和参数 | 库存 | 价格 | ||
|---|---|---|---|---|---|---|
 | 7Z08272Energy Sensor Adapter, Connect PE-C and PD-C to Nova Meter | 有库存 |
PE-C to PE Size Adapter
The newer PE-C series sensors have a Ø62 mm diameter. The older PE series sensors have a Ø85 mm diameter. This adapter allows using the PE-C type sensors in jigs and setups that were originally designed for PE sensors.
Beam Splitter Assembly for Pyro
Beam Splitter Assembly to measure pulsed laser sources too energetic for direct measurement. The reading with the Beam Splitter can be calibrated by setting the laser to a lower energy that will not damage the sensor and then taking a measurement with the beam splitter and without and taking the ratio.
PE-C Sensor Protective Cover
The PE-C sensor protective cover safeguards the sensor from dust and damage when not in use. Designed for PE-C sensors without a diffuser, this accessory is included with the sensor but is also available for individual purchase.
Damage Threshold Test Plates (Metallic)
Test plates with same absorber coating as the sensor. For testing that laser beam is not above damage threshold (1 such plate is included with sensor package).
Fixed extension cables for Energy Sensors
Order a fixed extension cable along with sensor to receive a different cable than the standard 1.5 m cable.
Modular extension cables for Energy Sensors
The extension cables can be ordered separately from the sensors.
Extended Warranty for Sensor
Customers that purchase the above items also consider the following items. Ophir-Spiricon meters and sensors include a standard manufacturers warranty for one year. Add a one year Extended Warranty to your meter or sensor, which includes one recalibration.
| 对比 | 型号 | 图纸、CAD和参数 | 库存 | 价格 | ||
|---|---|---|---|---|---|---|
 | XWAR-SENSORExtended Warranty for Sensor |
