PD300RM-UV | LED Measurement | Power Sensors - Ophir

PD300RM-UV

7Z02479
Описание: 

Радиометр PD300RM-UV для лазеров и светодиодов заменяет традиционные радиометры, откалиброванные для одной длины волны (254 нм, 365 нм и т. д.). Он откалиброван для более широкого спектрального диапазона, к которому можно получить доступ, введя любую длину волны в диапазоне калибровки. PD300RM — это круговой датчик дозировки и интенсивности излучения светодиода общего назначения. Он имеет апертуру 8 мм и оснащен рассеивателем с косинусоидальной корректировкой. Спектральный диапазон: 200—850 нм; диапазон измерения излучения: от 15 нВт/см² до 250 мВт/см². Датчик поставляется с 1,5-метровым кабелем для подключения к измерителю или интерфейсу компьютера.

Specification

  • Ø8mm
  • 200-850nm
  • 100nW/cm²-250mW/cm²
  • Ø35 W x 21 D (mm)
  • 10W/cm²
  • 0.2 s
  • -0.03%/°C
  • 5%
  • CE, UKCA, China RoHS
Need help finding the right sensor? Try our Поиск датчиков

FAQ

Can I measure white LEDs with the PD300RM?

No, white LEDs have wideband spectrum. Try the PD300CIE for illuminance (lux) measurement.

Was this FAQ helpful to you? yes no
Close

Can I measure a laser with the PD300RM?

Yes, in applications where a laser beam is diverging or diffused, such as laser projectors, PD300RM can be used to measure the irradiance with high accuracy. However, it is not applicable for measuring a collimated laser beam. Use the PD300 for that.

Was this FAQ helpful to you? yes no
Close

Can I measure a mercury lamp with the PD300RM-UV?

No, the PD300RM is a broadband detector. It doesn’t have a filter to isolate specific emission lines such as mercury lamp lines (365nm, 254nm) or spectral bands such as UVA, UVB. Custom solutions with filters are available; contact Ophir for more information.

Was this FAQ helpful to you? yes no
Close

What is the accuracy of the PD300RM for LEDs and for lasers?

The accuracy when measuring irradiance of laser sources is easy to determine because lasers have very narrow bandwidth and their wavelength is well known. The accuracy for laser measurement is given in the specifications. When measuring the irradiance of LED sources, other issues such as bandwidth and wavelength tolerance come into play. For more details and specifications see the white paper.

Was this FAQ helpful to you? yes no
Close

What is the purpose of the PD300RM's diffuser?

In order to get a good cosine corrected response, a diffuser is placed in front of the photodiode to convert directional light into lambertian diffused light, thus eliminating any sensitivity to direction.

Was this FAQ helpful to you? yes no
Close

Do I need to recalibrate my instrument? How often must it be recalibrated?

Unless otherwise indicated, Ophir sensors and meters should be recalibrated within 18 months after initial purchase, and then once a year after that.

Was this FAQ helpful to you? yes no
Close

Videos

Measuring LED Irradiance and Dosage with the PD300RM Measuring LED Irradiance and Dosage with the PD300RM
Measuring Power of LEDs: UV, Visible and NIR Measuring Power of LEDs: UV, Visible and NIR Measuring Power of LEDs: UV, Visible and NIR

Measuring the emitted power of an LED can be tricky; it is different in some important ways from measuring the power of a laser beam. This video shows you how to use the Ophir 3A-IS Integrating Sphere Sensor, along with the Auxiliary LED accessory, to easily make accurate measurements in LED applications.

Does your application involve irradiating a target surface with an LED? UV curing of adhesives is one example of such an application. Ophir’s new PD300RM sensor family measures irradiance and dosage for UV and Visible LEDs. This video explains what the PD300RM does, what is so unique about it, and how to use it.

Tutorials

Tutorials and Articles

White Paper – Measuring LED Power and Irradiance with Calibrated Photodiodes

In many industries LEDs are replacing traditional broadband light sources such as mercury, deuterium, Xenon, and quartz-halogen lamps. Systems and applications transitioning to LEDs are reengineered in terms of optics, electronics, heat management and more. Similarly, the equipment used by professionals to measure the output of these sources needs to be fitted for measuring LEDs.

 Прочитать подробнее…

Applications: Designing Low Cost Inspection Process for LED’s

By Dan Ford Southwest Regional Sales Engineer, Ophir Photonics Group Прочитать подробнее…

Fighting Viruses

The world remains in a continuing state of uncertainty due to the new COVID-19 coronavirus. Face masks and disinfectants are selling very well. Disinfection with UV light could offer a way of disinfecting larger areas without the use of chemical disinfectants, especially in hospitals where patients are being treated. Прочитать подробнее…

Measuring Broadband UVA And Violet Led Light Sources For Industrial And Medical Applications

As the development of new UV LED sources continues at an ever-growing pace, so do the industrial applications that utilize them. UV LEDs are being put to work in various industrial processes, medical applications, and – especially due to COVID-19 – increasingly used to develop solutions for disinfection purposes. Efficient utilization of the UV radiation requires good measurement tools. However, accurate light measurement in this spectral range presents challenges, such as how to accurately measure the irradiance if the wavelength of the light is not known. Прочитать подробнее…

Accessories

Customers that purchase the above items also consider the following items. Ophir-Spiricon meters and sensors include a standard manufacturers warranty for one year. Add a one year Extended Warranty to your meter or sensor, which includes one recalibration.
  • Cable

    5m Cable

    7E01125A

    * Order only with purchase of a sensor.
    5m cable to connect sensor to power meter or interface. Order along with sensor to receive this instead of the standard 1.5m cable.

  • 10m cable

    10m Cable

    7E01125B

    * Order only with purchase of a sensor.
    10m cable to connect sensor to power meter or interface. Order along with sensor to receive this instead of the standard 1.5m cable.