FC Fiber Adapter

FC ファイバーアダプター

7Z08229
 
概要: 

このファイバーアダプターは、パワーセンサーとエネルギーセンサーを標準のFCタイプファイバーに接続するために使用します。 多くのセンサーは、すべてのファイバーアダプターに接続するための追加の取り付けブラケットが必要です。 詳細については、以下のデータシートをご覧ください。

御見積り センサファインダ

仕様

Photodiode Sensors Datasheet
Thermal Sensors Datasheet
Pyroelectric Sensors Datasheet
  • Ø25mm x 8mm
  • All but PD300
  • ST
センサのモデル選択には、センサファインダが便利です。
または弊社までお気軽にお問合せください。

FAQ

Do the fast photodiode detectors (FPD & FPS-1) have attenuators and fiber adapters available for them?

Yes, there are a variety of accessories such as attenuators and fiber adapters available for the FPD & FPS-1 Fast Photodiode Detectors. Fast Photodiode Detectors are used for displaying temporal pulse shape on an oscilloscope. Please note that in order to mount these accessories to the FPS-1 you will need the SM1-to-M20 adapter 1G02259. This is mentioned in the catalog spec page but is sometimes missed. No adapter is needed for FPD models.

Was this FAQ helpful to you? yes no
閉じる

ファイバアダプタを使用する際に、ファイバ使用と校正におけるパワーの損出をどのように扱ったらよいでしょうか？

オフィール社のフォトダイオードセンサを含む全てのパワーメータは、ファイバ端からセンサまで空間があります。

大気中でのファイバから照射されたパワーを測定するので、反射によるファイバ光の損失は考慮していません。実際の測定に際には、損失が起こらないようにファイバを接続した上で、損失値を読み値に追加します。損失率は一般的に4％程度です。従ってパワーメータでの読み値が100mWの場合、実際のパワーは104mWということになります。測定を行う前にお気軽にご相談ください。

Was this FAQ helpful to you? yes no
閉じる

PD300に付属の外部フィルタ装着した状態で、同時にファイバアダプタを使用できますか？

可能です。PD300に外部フィルタを装着した場合でも、未装着でもファイバアダプタを使用できます。

Was this FAQ helpful to you? yes no
閉じる

計測器は校正を受ける必要がありますか。ある場合、校正を受ける頻度をお知らせください。

特に指定がない限り、オフィールのセンサー及びディスプレイは購入日から18か月以内に初回の校正を受けて頂く事をお勧め致します。その後は年次定期校正を受けて頂く事を推奨致します。

Was this FAQ helpful to you? yes no
閉じる

To connect a fiber to an Ophir sensor, why do I need 2 items – an “Adapter” and a “Mounting Bracket”

The idea is used with most (though not all) sensors; the fiber optic connectors are standard (such as FC, SMA, etc.), but the sensors are all different in their mechanics, so we use the standard FO connectors but provide in addition mounting brackets for connecting the FO connectors to the various sensors.

Was this FAQ helpful to you? yes no
閉じる

動画

光ファイバから照射されたビームのパワー測定 光ファイバから照射されたビームのパワー測定

光ファイバから照射されたビームの出力測定についての留意点

チュートリアル&ブログ

チュートリアル

Fiber Adapter accessory

When using a Fiber Adapter accessory together with one of Ophir's sensors, it is important to be aware of the power/energy density that is going to reach the sensor's surface.In most cases, the fiber adapter locates the fiber tip far enough away from the absorber surface that the spot diameter on the surface will be large, and problems of damage avoided. However, that is not always a certainty! For example, when using a sensor from the PD300 series, especially with filter IN, this distance could be quite small. A power level that is within spec limits could still result in a power 詳細を見る

Measuring Power out of a Fiber

We recently came across an interesting customer problem, in which every time he disconnected the FO connector from the adapter (that is mounted on the sensor) and then reconnected it, the power read about 50-100 uW higher than it did (nothing else changed). It then took about 10 minutes to slowly come back down to what it had been. After an investigation, we found that the increase in reading when disconnecting/reconnecting the fiber connector is a thermal effect, and not a technical flaw in the unit. If you experience something like this, the most likely direct cause is one of the following 詳細を見る

アクセサリ

上記のセンサに対応するアクセサリを各種ご用意しています。
  • Fiber Adapter Mounting Bracket

    30 BB/LP1/N Fiber Bracket

    7Z08211
    A mounting bracket is needed to connect most thermal sensors to a fiber adapter (SC, ST, FC or SMA). This bracket can be used for thermal sensors with an 18mm diameter.
  • 30 P/SV/HE Fiber Bracket

    30 P/SV/HE Fiber Bracket

    7Z08230
    A mounting bracket is needed to connect most thermal sensors to a fiber adapter (SC, ST, FC or SMA). This bracket can be used for thermal sensors with a 17mm diameter.
  • 50(150)/F150 Fiber Bracket

    50(150)/F150 Fiber Bracket

    7Z08210
    A mounting bracket is needed to connect most thermal sensors to a fiber adapter (SC, ST, FC or SMA). This bracket can be used for thermal sensors with a 26mm diameter.
  • L50/FL250 Fiber Bracket

    L50/FL250 Fiber Bracket

    7Z08265
    A mounting bracket is needed to connect most thermal sensors to a fiber adapter (SC, ST, FC or SMA). This bracket can be used for thermal sensors with a 35mm diameter.
  • L40(150)/L50(150) Fiber Bracket

    L40(150)/L50(150) Fiber Bracket

    7Z08238
    A mounting bracket is needed to connect most thermal sensors to a fiber adapter (SC, ST, FC or SMA). This bracket can be used for thermal sensors with a 50mm diameter. This is a unique bracket which can be attached to three adapters to measure three fiber inputs simultaneously.
  • FL250/FL400 Fiber Bracket

    FL250/FL400 Fiber Bracket

    7Z08212
    A mounting bracket is needed to connect most thermal sensors to a fiber adapter (SC, ST, FC or SMA). This bracket can be used for fan-cooled thermal sensors with a 50mm diameter.
  • 3A-IS Fiber Adapter Bracket

    3A-IS Fiber Adapter Bracket

    7Z08213
    A mounting bracket is needed to connect most power and energy sensors to a fiber adapter (SC, ST, FC or SMA). This bracket can be used for integrating sphere models 3A-IS and 3A-IS-IRG.
  • PD10 Fiber Adapter Bracket

    PD10 Fiber Adapter Bracket

    7Z08275
    A mounting bracket is needed to connect most power and energy sensors to a fiber adapter (SC, ST, FC or SMA). This bracket can be used for photodiode energy sensors in the PD10 series.
  • PE50 Fiber Adapter Bracket

    PE50 Fiber Adapter Bracket

    7Z08270
    A mounting bracket is needed to connect most power and energy sensors to a fiber adapter (SC, ST, FC or SMA). This bracket can be used for pyroelectric energy sensors in the PE50 series. It is not compatible with diffuser-equipped sensors.
  • PE9/PE10/PE25-C Fiber Bracket

    PE9/PE10/PE25-C Fiber Bracket

    7Z08269
    A mounting bracket is needed to connect most power and energy sensors to a fiber adapter (SC, ST, FC or SMA). This bracket can be used for pyroelectric energy sensors in the PE9, PE10 and PE25 series. It is not compatible with diffuser-equipped sensors.

関連製品