BeamSquared software, software license, XC-130 USB 2.0 camera, optical train, automatic and manual operation, recommended for 900nm - 1700nm wavelengths.御見積り
BGP license for BSQ-XC130SP90508
Includes BeamGage Professional software license in addition to BeamSquared software license御見積り
Are the BeamSquared lenses interchangeable from one BeamSquared unit to another?
Because of the design of the lenses for the new BeamSquared, you will be able to use lenses on multiple systems. We have included an RFID chip on each lens which holds the information for that lens. We have also programmed the BeamSquared optical trains to have their calibration information stored in the device. With this improvement the configuration files for pairing optical trains and lenses are no longer required making lenses interchangable.閉じる
Can any BeamGage camera be used with a BeamSquared system?
BeamGage systems and BeamSquared systems are separate and the cameras with them are not always interchangeable. However, if you currently have an SP300, SP920, XC-130, or one of our Pyrocam IIIHR or IV cameras, you can upgrade these cameras to be compatible with the BeamSquared software (Note: Pyrocams are not compatible with the optical train).
The cameras sold with BeamSquared systems are not licensed for use with BeamGage. This is an optional item that can be purchased that would allow further analysis with the camera outside of the BeamSquared software.
Does the BeamSquared internally provide all the necessary attenuation for operation with the direct laser beam?
Before allowing laser energy to enter the instrument, it is important to limit the beam intensity. Excessive laser energy may cause damage to the camera or the internal components of the BeamSquared optical train.
Typically, a CCD camera sensor can be damaged at energy levels in excess of 1 mJ/cm² or at power levels greater than .15 mW/cm². Adjust these input limits downward based on the likely focused spot size resulting from your M² lens focal length. Beam splitters and/or filters may be used to attenuate the beam, but care must be used to prevent the introduction of distortions.
During an M² measurement operation, the peak energy density that reaches the camera will change, potentially over several orders of magnitude. This is a result of the camera effectively moving from a larger unfocused spot near the lens, into and through the focus at the waist, and then out again to an unfocused spot (see the Adjusting Brightness section in the manual). The Linear attenuators in the optical train will automatically adjust to accommodate these changes in beam intensity, so long as the operator, has prudently selected the initial beam intensity. Thus, it is the operator's responsibility to attenuate the laser sufficiently to operate within the safe dynamic range of the BeamSquared system.閉じる
When in the laser life cycle is the M2 measurement the most important?
M² measurement is important if the stability of your laser is important to your process. Taking M² measurements on a frequent basis allows you to see if your laser is stable from time to time. If the results of the M² measurement fluctuate and a noticeable change happens over time, this could help identify problems with consistency in the laser and help prevent negative results to your process where the laser is being utilized.閉じる
Why can my M² unit have an M² measurement less than 1?
There are two common occurrences when M² results are less than 1. The first and most common of these results from the operator entering the wrong wavelength value. In this case the results are often well below 1, in the .8-.9 range. The second most common cause is due to nominal accuracy tolerances. These are normal and expected. With a 5% M² tolerance results from ~.95 to ~1.05 are possible. Averaging runs will normally return a mean value to something > 1, but not always.
It has been suggested that if the M² results are computed to be < 1 we should display a 1 as the answer. However the algorithms in the BeamSquared software make computations and report results as the input settings and the beam samples dictate. This is done to provide useful information to the operator rather than to try and conceal the issue.閉じる
I have an M2-200s unit and a BeamSquared. Can I run both from the same computer?
The two software programs and their motion controller drivers cannot be installed concurrently. The M2-200s software only supports up to Windows 7 operating systems and uses older motion controller drivers where the BeamSquared software supports up to Windows 10 and uses updated motion controller drivers that are not compatible with the M2-200s system.
To operate them from the same computer requires that the computer be a Windows 7 operating system and that you uninstall the previous program including the motion controller drivers first, then reboot the computer before you can install the other software with its motion controller drivers.
Now you can automatically measure laser beam quality (M2) in under one minute and tune your laser for best operation.
BeamSquared system is a compact and fully automated tool for measuring the propagation characteristics of CW and pulsed laser systems from the UV to NIR to Telecom wavelengths. You can also measure wavelengths above 1.8 microns, including CO2 and terahertz in manual mode (a bench set-up; without the automated optical train) with a Pyrocam IV or IIIHR.
BeamSquared, a compact and fully automated tool for measuring the propagation characteristics of continuous wave and pulsed laser systems from the UV to NIR to Telecom wavelengths.
An SP920 camera licensed for BeamSquared. Sold as an accessory for those also purchasing a BSQ-XC130
BSQ-Lens Kit 266-1550SP90449
Lens kit that includes 5 BeamSquared lenses: 500mm UV, 500mm VIS, 400mm VIS, 400mm NIR, 400mm XNIR.
BSQ-Lens Kit 650-1700SP90450
Lens kit that includes 2 BeamSquared lenses: 400mm NIR, and 400mm XNIR.
BSQ-Lens UV 500mmSP90451
Single BeamSquared lens, 500mm focal length, A/R coated for 266-440nm
BSQ-Lens VIS 500mmSP90452
Single BeamSquared lens, 500mm focal length, A/R coated for 430-700nm
BSQ-Lens VIS 400mmSP90453
Single BeamSquared lens, 400mm focal length, A/R coated for 430-700nm
BSQ-Lens NIR 400mmSP90454
Single BeamSquared lens, 400mm focal length, A/R coated for 650-1000nm
BSQ-Lens XNIR 400mmSP90455
Single BeamSquared lens, 400mm focal length, A/R coated for 1000-1550nm
BSQ-Lens XNIR 600mmSP90485
Single BeamSquared lens, 600mm focal length, A/R coated for 1000-1550nm
BSQ-Lens UV 750mmSP90554
Single BeamSquared lens, 750mm focal length, A/R coated for 245-440nm
BSQ-Lens VIS 750mmSP90555
Single BeamSquared lens, 750mm focal length, A/R coated for 430-700nm
BSQ-Lens NIR 750mmSP90556
Single BeamSquared lens, 750mm focal length, A/R coated for 650-1000nm
BSQ-Lens XNIR 750mmSP90557
Single BeamSquared lens, 750mm focal length, A/R coated for 1000-1550nm
BSQ-Lens UV 1000mmSP90558
Single BeamSquared lens, 1000mm focal length, A/R coated for 245-440nm
BSQ-Lens VIS 1000mmSP90559
Single BeamSquared lens, 1000mm focal length, A/R coated for 430-700nm
BSQ SP300 to SP920 upgradeSP90511