Der PD300-BB-50mW radiometrische Sensor verfügt über einen flachen Photodioden-Sensor um breitbandige Lichtquellen zu messen. Er deckt den Spektralbereich von 430 bis 1000nm ab und hat eine 10x10mm Apertur mit einer schwenkbaren Halterung. Ohne Filter liegt sein Leistungsmessbereich zwischen 50pW und 4mW. Mit Filter liegt er zwischen 1nW und 50mW. Der Sensor wird zum Anschluss an ein Messgerät oder eine PC-Schnittstelle mit einem 1,5 Meter langen Kabel geliefert.
Catalog & Manuals
I am using a PD300 type sensor. I have a broadband light source, but only want to measure the power of a specific wavelength. Can I set my meter to that wavelength and get a measurement?
The PD300 series of photodiode-based sensors are calibrated with a full spectral curve using a scanning monochromator (plus a few laser "anchor points").
The wavelength ("Laser") setting tells the meter what wavelength is being used and hence what calibration factor to apply when a measurement is underway. It does not, however, physically limit the possibility of other wavelengths from entering. All light (within the sensor's specified range of course) entering the detector will be measured; the meter will apply the calibration factor meant for the selected wavelength, "thinking" that only that wavelength is present.
In other words, these sensors assume a monochromatic light source. Their relative spectral response is not flat and they are therefore not suited for broadband beams.
So, if you want to check one wavelength from a broadband source, you will need to use a wavelength filter that only passes that wavelength. Then you should set your meter to the appropriate wavelength to account for the detector's relative sensitivity.Close
When using a photodiode laser power sensor to measure very low power pulsed beams (nW to mW), there are some issues you need to be aware of. This video shows you how to avoid some common problems and ensure maximum accuracy.
This video explains how to use Ophir sensors and meters to measure the power or energy of broadband light sources such as solar radiation, flash lamps, LEDs etc.
In this short "Basics" video, we review in general the use of photodiode sensors for measuring very low laser powers.
In this short “Basics” video, we review in general the use of photodiode sensors for measuring very low laser powers.
Laser Power Sensors introduction
As described in the general introduction, the thermopile sensor has a series of bimetallic junctions. A temperature difference between any two junctions causes a voltage to be formed between the two junctions. Since the junctions are in series and the «hot» junctions are always on the inner, hotter side, and the «cold» junctions are on the outer, cooler side, radial heat flow on the disc causes a voltage proportional to the power input. Laser power impinges on the center of the thermopile sensor disk (on the reverse side of the thermopile), flows radially and is cooled on the periphery. The array of thermocouples measures the temperature gradient, which is proportional to the incident or absorbed power. In principle, the reading is not dependent on the ambient temperature since only the temperature difference affects the voltage generated and the voltage difference depends only on the heat flow, not on the ambient temperature. Weiterlesen...
Common Reasons for Photodiode Sensor Damage or Out of Tolerance Conditions
We have included this document with your recent calibration order because we have noticed an out of tolerance condition obtained from your equipment when returned for calibration. This document was created to assist our valued customers in the proper care and maintenance of Ophir photodiode sensors. The following information is for reference only. If you have any reason to believe that the sensor is no longer performing within the original specifications, we always recommend that you send it in for repair and/or recalibration by our trained technicians to bring the unit back to the proper NIST traceable standards.
Ophir photodiode sensors can be used for many years without any repairs when used with the proper laser optical setup. Many of our customers have sensors that are using their original absorber that are over ten years of age. We hope that this document will enable you to also enjoy the long life and reliable results that Ophir- Spiricon is known for. Weiterlesen...
How to Properly Select a Laser Power or Energy Sensor
The selection of a sensor to accurately measure the power of a laser or energy of a pulsed laser can seem like a simple and easy procedure. However, many times the selection process is limited to choosing a sensor that only meets the range of power or energy to be measured, leaving out several other essential criteria of the laser specifications; that without their consideration, can allow the wrong sensor to be selected, the laser to be measured inaccurately and likely to cause the sensor to fail prematurely.Weiterlesen...
Effect of Ambient Conditions on Laser Measurements
We are often asked about the specified ranges of various ambient conditions (temperature, humidity, etc.) for Ophir instruments. In this article we will clarify the effects of these conditions on laser measurements, so you’ll be able to use your Ophir laser measurement instrument effectively. Weiterlesen...
Online Sensor Finder
- 120 L x 13 W x 21 D (mm)
- 0.2 s
- CE, China RoHS
Ø7mm aperture CDRH adapter for PD300 series.
(Dimensions: 42 L x 21.4 W x 12.5 D (mm))
Ø3.5mm aperture CDRH adapter for PD300 series
(Dimensions: 42 L x 21.4 W x 12.5 D (mm))
7Z08221This fiber adapter is used to connect a rectangular PD300 sensor directly to a standard SC-type fiber. No mounting bracket is necessary.
7Z02210This fiber adapter is used to connect a rectangular PD300 sensor directly to a standard ST-type fiber. No mounting bracket is necessary.
7Z02213This fiber adapter is used to connect a rectangular PD300 sensor directly to a standard FC-type fiber. No mounting bracket is necessary.
7Z02212This fiber adapter is used to connect a rectangular PD300 sensor directly to a standard SMA-type fiber. No mounting bracket is necessary.