ModeCheck für 10.6 μm
Das ModeCheck Strahlprofilmessgerät für gebündelte CO2 Laser misst und analysiert industrielle Laser mit Wellenlängen um 10,6 µm, in dem es mit einem schnell drehenden Spiegel nur einen Teil des Strahl erfasst. Der Laserstrahl wird bei dieser Technik nahezu unverändert durchgelassen. Das System bietet ein kompaktes, ultraleichtes Design, das sich ideal für die regelmäßige Messung von CO2 Lasern in Schneid- und Schweißprozessen eignet.
- 5mm - 40mm
- Silcon CMOS Camera
- USB 2.0
- 100W - >5kW
- CE, China RoHS
ModeCheck, CO2 sampler for 10.6μm beams up to 5kW, beam width up to 30mm; includes 2 user selectable wands from selection belowAngebot anfragen
- ModeCheck Beam Analysis SoftwareModeCheck comes with its own full-function software is designed with a simple interface for both laser technicians and every day laser users. It provides all of the calculations real-time and a customizable under interface with the ease-of-use and flexibility that customers have come to expect.
I have damaged my fluorescent imaging plate. Can I replace it or do I need to send it back to the factory for repair?
Why will my ModeCheck not finish its background calibration cycle?
The ModeCheck background calibration cycle may get stuck due to some environmental conditions which cause the wand position to become difficult to determine. You may be able to restore operation by cleaning the back side of the wand where the wand passes the optical sensor.Close
Does the ModeCheck work at wavelengths other than 10.6μm CO2?
Can I correlate my power meter reading from my Ophir sensor with the data from the ModeCheck?
Yes, click on the Computations tab and enter the reading from your Ophir power meter equipment into the Calibration Value editbox on the Power panel and click on the Calibrate button (checkmark) to correlate the Ophir power meter reading with your beam profile.Close
VideosIndustrial Laser Beam Measurement with ModeCheck Industrial Laser Beam Measurement with ModeCheck
Watch as this operator tunes his laser.
Dr. Roundy, early laser diagnostic pioneer, explains why it is important to measure your laser beam.
ModeCheck enables Quality Cutting, Marking, Drilling & Ablating. Instantaneously "see" and measure your beam and reduce set-up time between jobs. ModeCheck provides real-time "mode burns" - eliminate hazardous acrylic vapors. Optimize your lasers efficiency - reduce cost per part, predict laser preventative maintenance, increase manufacturing efficiency. Visit www.ophiropt.com/photonics for details.
The Importance of CO2 Laser Optimization
Ensuring High Cutting Speeds Through Accurate Beam Power Measurements in Multi-Kilowatt CO² Laser Machines
Beam Profile of 10kW CO2 Laser
0.5% beam wand sampler, see damage and saturation chart
1% beam wand sampler, see damage and saturation chart
2% beam wand sampler, see damage and saturation chart
4% beam wand sampler, see damage and saturation chart
10% beam wand sampler, see damage and saturation chart
Beam Dump; 5kWSP90224
Beam dump for up to 5kW continuous, includes mounting bracket, requires continuous water flow
Power sensor, measure CO2 power up to 5000W; water cooling needed
Mounting Hardware, 5000W detectorSP90212
Mounting hardware for 5kW power sensor. Required when ordering the 5000W-SH sensor
Power sensor, measure CO2 power up to 10,000W; water cooling needed
Mounting Hardware, 10,000W detectorSP90213
Mounting hardware for 10KW power sensor. Required when ordering the 10kW-SH-V2 senso
ModeCheck storage/carrying caseSP90227
Ruggedized ModeCheck storage/carrying case
Collimating 2” Lens AdapterSP90329
ModeCheck Lens Adapter (MLA) enables a ModeCheck to recollimate a focused CO2 laser beam. MLA should be ordered with the ModeCheck so that it can be factory installed.