LBS-400 Attenuator
LBS-400 Attenuator

LBS-400衰减器

Pyrocam相机适用的中性密度滤光片和光学取样系统
 
描述: 

LBS-400光束取样器可配合Pyrocam 相机，可测量直径最高达1英寸（25.4mm）、功率为10mW~500W(1)的UV或IR波长激光光束。光束取样器在设计上消除了单光楔的优先偏振选择效应，能得到经偏振校正的光束图像，以还原原光束的偏振分量。

(1)For Gaussian beam diameter <1/2 the clear aperture and depending on ND filter and camera saturation limits the maximum power may be as high as 1200W.

联系我们 轮廓分析向导

Specification

Datasheet
  • Proprietary
  • LBS-400-UV: 193-355nm, LBS-400-NIR: 1064nm, LBS-400-IR: 10.6μm
  • LBS-400-IR: 5W/cm² 300J/cm²for 1ms pulse / LBS-400-UV: 100W/cm² 20mJ/cm² for 10ns pulse / LBS-400-NIR: 50W/cm² 1J/cm² for 10ns pulse
  • LBS-400-UV: A/R ≤1.5%, LBS-400-NIR: A/R ≤1%, LBS-400-IR: A/R ≤1%
  • LBS-400-UV: Inconel, LBS-400-NIR: Bulk ND, LBS-400-IR: CaF2
  • 31.75mm
Need help finding the right beam profiler? Try our Beam Profiler Finder

Ordering

The LBS-400 combination beam sampling and beam apsorption systems available with the following options.

  • LBS-400-UV

    SP90351

    Beam sampler attachment for Pyrocam cameras for measuring UV wavelength laser beams with diameters up to 1 inch (25.4mm) and powers ranging from 10mW to ~500W

    询问报价

  • LBS-400-NIR

    SP90354

    Beam sampler attachment for Pyrocam cameras for measuring NIR wavelength laser beams with diameters up to 1 inch (25.4mm) and powers ranging from 10mW to ~500W

    询问报价

  • LBS-400-IR

    SP90349

    Beam sampler attachment for Pyrocam cameras for measuring IR wavelength laser beams with diameters up to 1 inch (25.4mm) and powers ranging from 10mW to ~500W

    询问报价

  • LBS-400 C-Mount Adapter

    SP90352

    Adaptor plate to mount C-Mount devices to LBS-400

    询问报价

  • LBS-400 to L11059 Adapter

    SP90439

    Adaptor plate to mount L11059 camera to LBS-400

    询问报价

  • LBS-400 to Pyrocam Adapter

    SP90510

    Adaptor plate to mount Pyrocam IV camera to LBS-400

    询问报价

FAQ

What should be my Safety concerns while using LBS-400?

Regular laser safety precautions should apply. Please note, that the main incident beam will exit the LBS-400 refracted approximately 6°. Provision must be made to safely contain the transmitted beam by beam dump or power meter.

Was this FAQ helpful to you? yes no
Close

How to deal with removable Beam Blocker?

The beam blocker is designated to keep one wedge surface protected during handling and shipping. It can be left attached for low power laser operations. However, in the case of high-power laser irradiation scattered light might interfere with beam profile measurement and cause offset. In case of such offset, we recommend removing the beam blocker.

After removal, an additional laser output, having less than 0.1% of incident beam power will be reflected. That beam could be used for simultaneous measurement of laser power via Ophir Power Meter in addition to beam profiler.

Was this FAQ helpful to you? yes no
Close

Can I use LBS-400 both for beam profiling and power measurement?

Yes, the main function of LBS-400 beam splitter is Beam profiling, however it performs a 3-way beam splitting:
Less than 0.01% (1/103) of the beam is reflected in one direction and less than 1% in another while remaining 99% of incident laser beam is transmitted.
This allows user to measure one of the 3 beams, depends on available power measurement equipment and setup convenience.

Was this FAQ helpful to you? yes no
Close

Support

Tutorials and Articles

Imaging UV light with CCD Cameras

Is it possible to image a UV laser with a Silicon Sensor CCD camera offered by Ophir-Spiricon? The answer is yes, but the direct UV light ablates Silicon CCD chips over time. The ablation is cumulative and depends on the intensity, the wavelength, and the duration of the light on the sensor. The best choice for imaging UV light without damage is to avoid directly imaging the beam on the CCD sensor by using an UV image converter... 阅读更多...

Integrated Solutions: Interconnecting Ophir Products and Accessories

The Concept: Ophir customers often need to connect different optical components together to create an optimal setup to best meet their needs. In order to do this, Ophir provides mutual interconnections between different Ophir products via adapters with various threads, designed to exactly fit required optical path distances for each device. This is an integrated solution, prealigned and ready to use. 阅读更多...