50(150)A-BB-26-PPS | BeamTrack Power / Position / Size Sensors | Power Sensors - Ophir

50(150)A-BB-26-PPS

7Z07900

Датчик лазерных измерений 50(150)A-BB-26-PPS серии BeamTrack измеряет размер и положение лазерного пучка, а также мощность и энергию. Датчик имеет апертуру 26 мм и может измерять размер пучка с точностью до 5% и положение пучка с точностью до 0,1 мм. Диапазон измерения мощности: от 40 мВт до 50 Вт в непрерывном режиме; в кратковременном режиме максимальное измеряемое значение составляет 150 Вт.

Прочитать подробнее…
50(150)A-BB-26-PPS | BeamTrack Power / Position / Size Sensors | Power Sensors - Ophir
50(150)A-BB-26-PPS | BeamTrack Power / Position / Size Sensors | Power Sensors - Ophir
  • Ø26mm
  • 0.19-20µm
  • 40mW-150W
  • 20mJ-100J
  • 64 L x 64 W x 64 D (mm)
  • 100J
  • 12kW/cm²
  • 1.5 s
  • 0.3J/cm²
  • 10J/cm²
  • 150W
  • Power/Energy/Position/Size
Need help finding the right sensor? Try our Поиск датчиков

Can I measure position and size of a pulsed laser using a BeamTrack sensor?

Position and Size are measured along with power. Therefore, if the laser is pulsing at a rate at which average power can be measured, then position and size can be measured as well.

Was this FAQ helpful to you? yes no
Close

When using a BeamTrack sensor with StarLab on a PC, can I have StarLab log Position and Size data? At what sampling rate?

Yes StarLab can log beam position. The BeamTrack sensors are thermal sensors. The power measurements for all Ophir power sensors are logged at 15 times a second. When a BeamTrack sensor is connected to StarLab via a Juno, the position / size measurements are also logged 15 times a second. When a BeamTrack sensor is connected to StarLab via a Vega/ Nova II, the position / size measurements are logged once a second. This is because in the Vega / Nova II we sample these parameters slower.

Was this FAQ helpful to you? yes no
Close

Are BeamTrack sensors backwards compatible with the Nova-II, Vega and Juno devices?

The hardware of all of these devices supports the BeamTrack sensors however, the firmware may need to be upgraded. Click here for a free download of the latest firmware from our web site

Was this FAQ helpful to you? yes no
Close

For what type of laser spots can we measure position and size with BeamTrack sensors?

Position can be measured for any beam shape. Size can be measured to specified accuracy only for Gaussian (TEM00) beams. For other laser modes, size measurement is relative only.

Was this FAQ helpful to you? yes no
Close

What meters support the BeamTrack (PPS) sensors?

The Vega, Nova II, StarLite. StarBright and Juno support the BeamTrack (PPS) sensors. All other instruments can display power and single-shot energy of a BeamTrack sensor, but do not display beam position and size.

Was this FAQ helpful to you? yes no
Close

Do I need to recalibrate my instrument? How often must it be recalibrated?

Unless otherwise indicated, Ophir sensors and meters should be recalibrated within 18 months after initial purchase, and then once a year after that.

Was this FAQ helpful to you? yes no
Close
  • BeamTrack with StarLab

    Support for BeamTrack sensors with Vega, Nova II, Juno, EA-1, StarLite, and StarBright in StarLab application is now available.
    For all other meters and interfaces the BeamTrack sensor behaves like a standard thermopile sensor, and therefore it is not necessary to upgrade the embedded software of the sensor.

    Download Steps
    In order to upgrade the embedded software in the BeamTrack sensor with the StarLab application:

    • Attach BeamTrack sensor to a Juno (version 1.23 or higher), a Vega / Nova-II (version 2.28 or higher), a StarLite (version 1.22 or higher), or StarBright (version 1.30 or higher).
         To download the latest version of Juno, Vega, Nova-II, StarLite or StarBright software press here
    • Connect the meter to the PC and run StarLab (with version 3.20 or higher).
         To download the latest StarLab version press here
    • Enter the diagnostic screen and select to upgrade sensor software (version 1.05 or higher).
         To download the latest BeamTrack version press here

    Note: BeamTrack sensors can't be upgraded via EA-1 interface.

 
Ophir BeamTrack Sensor Series Measures Laser Power, Position & Size Ophir BeamTrack Sensor Series Measures Laser Power, Position & Size
FAQ: Sensors for Measuring Laser Power FAQ: Sensors for Measuring Laser Power FAQ: Sensors for Measuring Laser Power

In this short “Basics” video we review in general how one goes about measuring laser beam power, so that you’ll have a clear basic understanding of what the different sensor types are, and when you would use which type.

How do I measure power of broadband sources like flash lamps, some LEDs, or sunlight? How do I measure power of broadband sources like flash lamps, some LEDs, or sunlight? How do I measure power of broadband sources like flash lamps, some LEDs, or sunlight?

This video explains how to use Ophir sensors and meters to measure the power or energy of broadband light sources such as solar radiation, flash lamps, LEDs etc.

Ophir new BeamTrack Sensor Series, the industry’s first thermal sensors that combine power and energy measurement, beam position, and beam size in a single compact device.

Tutorials and Articles

Ophir Thermal BB Coating Power Meter Sensor Angular Dependence

For optimal accuracy the Ophir thermal power meter sensor will be placed in the beam path perpendicular to the incident beam. There is an angular dependence that will reduce the measurement accuracy by some percentage as is indicated in the chart below. It is recommended that the angularity not exceed 20-30 degrees in order to keep the error to an acceptable minimum. Прочитать подробнее…

Accessories

Customers that purchase the above items also consider the following items. Ophir-Spiricon meters and sensors include a standard manufacturers warranty for one year. Add a one year Extended Warranty to your meter or sensor, which includes one recalibration.
  • SC Fiber Adapter

    SC Fiber Adapter

    7Z08227
    This fiber adapter is used for connecting power and energy sensors to a standard SC-type fiber. Many sensors need an additional mounting bracket to connect to all fiber adapters. More information can be found in the datasheet below.
  • ST Fiber Adapter

    7Z08226
    This fiber adapter is used for connecting power and energy sensors to a standard ST-type fiber. Many sensors need an additional mounting bracket to connect to all fiber adapters. More information can be found in the datasheet below.
  • FC Fiber Adapter

    FC Fiber Adapter

    7Z08229
    This fiber adapter is used for connecting power and energy sensors to a standard FC-type fiber. Many sensors need an additional mounting bracket to connect to all fiber adapters. More information can be found in the datasheet below.
  • SMA Fiber Adapter

    SMA Fiber Adapter

    1G01236
    This fiber adapter is used for connecting power and energy sensors to a standard SMA-type fiber. Many sensors need an additional mounting bracket to connect to all fiber adapters. More information can be found in the datasheet below.
  • 26mm Fiber Adapter Bracket
    A mounting bracket is needed to connect most thermal sensors to a fiber adapter (SC, ST, FC or SMA). This bracket can be used for thermal sensors with a 26mm diameter.
  • SH to BNC Adapter

    SH to BNC Adapter

    7Z11010

    Allows connection of smart sensors to voltage measuring device for measurement of raw voltage output