LaserStar Laser Power & Energy Meter

LaserStar Dual Channel

7Z01601
Laser Power Meter & Energy Meter

The LaserStar is a microprocessor based laser power meter which is menu driven with window based software. Two models are available: single and dual channel.

  • Compatible with all standard Ophir Thermopile, Pyroelectric, Photodiode and RP sensors.
  • Large LCD display.
  • Backlighting & rechargeable battery.
  • Screen graphics and statistics (std div. min, ma...
Read more...
  • Yes
  • Yes
  • Yes
  • No
  • Yes
  • 1V
  • No
  • 30Hz
  • 1500Hz
  • N/A
  • N/A
  • 50K
  • No
  • Yes
  • PC Software & Drivers

    This section describes various ways to interface the Ophir meter to your PC as well as the software options available.


     

  • StarCom

    The StarCom application together with the Ophir meters that utilize the RS232 protocol turns your PC or laptop into a full-fledged Ophir laser power/energy meter. StarCom supports all major Ophir sensors. Supports the Nova, LaserStar, Nova-II, and Vega meters.

  • Ophir LabVIEW VIs for Dual Channel LaserStarOphir LabVIEW VIs for Dual Channel LaserStar
    VIs gives a complete measurement interface with Ophir's Single and Dual Channel LaserStar.

I have multiple sensors. Do I need a specific meter for each sensor or can I use one meter for all of my sensors?

With Ophir's Smart Head technology sensors can be interchanged between different meters easily. The calibration and setting information is stored in the sensors Smart Head connector so it moves with the sensor to the new meter. It is recommended that you power off your Nova meter before removing the sensor, but the new Nova II and Vega meters detect that a sensor has been removed or attached and will power cycle themselves when doing this.

Close

How does an energy meter measure above the maximum frequency at which it can record every pulse?

The energy meters will then sample at close to its maximum frequency. For instance measuring 10 KHz with a PD10 Sensor and Nova II where the maximum frequency for every pulse on the Nova II is 4 KHz: in this case, the Nova II will pick out pulses at a rate of close to 4 KHz and sample them, i.e. the Nova II will record 40% of the pulses.

Close

What is the Ophir meter zeroing and when should it be performed?

In all Ophir instruments, all adjustments, including zeroing internal circuits, are done from the software. This ensures simple and accurate realignment. The zeroing process helps eliminate internal biases in the unit which could affect accuracy of measurements. It is recommended to re-zero the instrument every 2 months for best performance. Specific instructions for doing this are found in the relevant User Manual for each instrument.

Close

Can I use a third party sensor with the Ophir power/energy meters?

No, only Ophir power/energy sensors with the Smart Head connection will work with the Ophir power/energy meters.

Close

Can the LaserStar work in dual channel mode with pyro and thermal sensors together?

It can work with any sensors in dual mode where they are operating separately but for ratio or difference it can only work with pyro vs. pyro or thermal/photodiode vs. thermal/photodiode.

Close
Easy Setup of an Ophir Power Meter and Sensor Easy Setup of an Ophir...

See how easy it is to setup an Ophir power meter and sensor to measure your laser's power and energy.

If you can't see the video please click here
Setting Your Laser Power Meter To a Custom Wavelength Setting Your Laser Power... Setting Your Laser Power Meter To a Custom Wavelength

Learn how to set the correct wavelength for your measurement, even when the wavelength you need is not one of the default wavelengths offered by the meter.

Accessories

Customers that purchase the above items also purchase the items below. Ophir-Spiricon meters and sensors include a standard manufacturers warranty for one year. Add a one year Extended Warranty to your meter or sensor, which includes one recalibration.
  • LaserStar Battery Pack

    7Z14006A

    Replacement battery pack for LaserStar

    $95.00
    In stock
  • LaserStar AN Adapter

    7Z11004

    LaserStar analog output adapter. Plugs into D25 output and provides analog output from BNC plug (1 unit supplied with LaserStar)

  • RS232 Cable for LaserStar

    7E01121

    Cable RS232 D9 - D25 (1 unit supplied with LaserStar)

Tutorials

  • Which Laser Power Meter is Right for You?

    Which Laser Power Meter is Right for You?

    We know that sometimes people really do want the all-in-one pen with compass et al, but other times they really just want the basic product. Before StarLite came around, you had two main options for a laser power meter. You could go down the Vega / Nova II route: top-of-the-line meters that can do pretty much anything you can think of doing with your laser power measurement. Then there’s the more basic meters (Nova / Laserstar), which still have some functionality, but are more affordable options for whomever doesn’t need the ultimate laser power meter.

  • How to Measure Different Wavelengths with a Laser Power Meter

    How to Measure Different Wavelengths with a Laser Power Meter

    There’s been some confusion lately about the “laser” setting on an Ophir power meter. Joe will ask: “What if my laser isn’t exactly one of the predetermined wavelengths? Will it still work?” Amanda says, “Can I set the Nova II to 633nm to check how much of that wavelength is in my broadband light source?”

  • Longer Length Sensor Cables

    Longer Length Sensor Cables

    The Ophir sensors are provided with a 1.5m cable between the sensor and the smart head connector. When a longer length cable is needed it can be provided, as long as it is within operational limits. However it is not possible to add an extension to the cable, because that moves the smart head connector away from the meter or interface unit which can degrade the smart head functionality or disable it.

For more tutorials click here