Quasar Wireless Interface Power Meter

Quasar

7Z01300
无线接口

Quasar模块提供了将Ophir传感器作为远程激光功率/能量计使用的一种方式,在无需连接线缆的情况下,实现传感器的优化放置寄PC或笔记本电脑的单独优化放置。

  • Quasar无线接口可连接到大多数标准Ophir传感器并广播到您的PC
  • 无线范围为10-30米,具体取决于周围环境
  • 使用可充电电池操作,通常一次充电可使用>40 小时
  • 将您的PC转变为一台完整的激光功率/能量计
  • 记录功率和能量、平均值、统计数据、柱状统计图及许多其它项目
  • 在一台PC上可同时监测最多7个Quasar

阅读更多...
Quasar Wireless Interface Power Meter
  • Yes
  • Yes
  • Yes
  • No
  • Yes
  • No
  • No
  • Internal Battery or Charger
  • N/A
  • N/A
  • N/A
  • N/A
  • 500Hz
  • No
  • No
  • No
Need help finding the right sensor? Try our 传感器查询

How far can the Quasar really transmit data and can it go through walls?

In actual testing done at customer sites, using the high power option, there was not a place within 100 meters that we could not connect, including going through multiple walls that were made of drywall. The only time we lost transmission was when the walls were made of concrete or we had to pass through some metal doors. With normal labs and offices the signal went right through. In several cases, including a solar power scribing application where windowed doors had to be closed, we were getting a continuous connection as we walked around the spacious building into offices and labs. With the standard range option, the range should be about 1/3 of this i.e. 30 meters.

Was this FAQ helpful to you? yes no
Close

At what frequency does the Quasar work? Might there be concerns with interference from other devices?

Quasar runs on Bluetooth, the 2.4-2.5GHz "ISM" band (ISM = Industrial, Scientific and Medical). This is the same band used by WiFi and other technologies. This frequency was chosen as it is available without restrictions around the world. Because other technologies also use it, Bluetooth has to be designed to tolerate interference from other sources. It does this by swapping between 79 channels, at 2.402GHz up to 2.480GHz (each channel is 1MHz). This type of modulation is called FHSS, Frequency Hopping Spread Spectrum. If data does not get through on one channel it retries on a different channel. Other technologies, such as WiFi, use different techniques.

 

This design makes Bluetooth very robust. In principle, if there is another radio transmitter nearby that is using the same 2.4-2.5GHz band AND using the same modulation scheme, interference is a possibility, but not a real likelihood. If the other transmitter is using a different band, there should not be a problem, because there is very little interference produced at other higher or lower frequencies - this is checked during qualification of these devices for CE and FCC in RF test labs.

 

In general, Bluetooth is in common use everywhere, by cellular phone headsets, for example, so interference is not normally a significant risk factor.

Was this FAQ helpful to you? yes no
Close

Will my Quasar work with my Android device?

Yes, we have an Android app that you can download from the Android Market place to run your Quasar on your Android device. Search for Ophir Optronics Quasar. You need to be running Android 2.3.3 or higher.

Was this FAQ helpful to you? yes no
Close

How do I pair the Quasar interface with my computer?

If using the Bluetooth radio USB adaptor supplied with the Quasar, the adaptor software should be installed first. Once that is complete, and the StarLab software installation is complete, you are ready to connect the Quasar. You may need to change the discovery settings on your PC to allow the Quasar to connect.
 

To accomplish this, go to the Bluetooth Settings on your PC and ensure you have checked "Allow Bluetooth devices to find this computer".

Was this FAQ helpful to you? yes no
Close

Do I need to recalibrate my instrument? How often must it be recalibrated?

Unless otherwise indicated, Ophir sensors and meters should be recalibrated within 18 months after initial purchase, and then once a year after that.

Was this FAQ helpful to you? yes no
Close
  • PC Software & Drivers

    This section describes various ways to interface the Ophir meter to your PC as well as the software options available.


     

  • StarLab

    The StarLab application together with an Ophir meter turns your PC or laptop into a full-fledged laser power/energy meter. Supports most Ophir laser power/energy sensors. Up to 8 sensors can be displayed at once on one PC. By using the Ophir COM Object, you can control the device from your own application. Supports the StarBright, StarLite, Juno, Nova II, Vega, Pulsar-1/2/4, Quasar, EA-1 and USBI devices.

  • StarViewer - Quasar
    StarViewer turns your Android based smartphone into a portable Ophir laser power/energy measurement monitor. It works with Ophir Thermopile and Photodiode based sensors that are attached to a Quasar.
  • Firmware - Quasar

    Embedded Software for Quasar Interface

    Latest Quasar firmware (version 1.25)

    Use StarLab to upgrade the firmware of your device. Press Here for step-by-step instructions.

Wireless Laser Measurements with Ophir’s Quasar Wireless Laser Measurements with Ophir’s Quasar
StarLab 3.0: Introduction and First Steps StarLab 3.0: Introduction and First Steps StarLab 3.0: Introduction and First Steps

This video explains the various items on the StarLab screen, and shows you how to perform basic laser measurements.
Part 1 of a series of video segments teaching you how to use StarLab.

StarLab 3.0: Second Steps StarLab 3.0: Second Steps StarLab 3.0: Second Steps

Sometimes we want to not only get a reading, but perform additional processing on the reading. This video shows you how to use various functions in StarLab, such as Averaging, Scale Factor, Normalize, Density, etc.

Laser Measurement PC Interfaces Laser Measurement PC Interfaces Laser Measurement PC Interfaces

If all your laser measurement work involves a laptop or a PC, rather than a stand-alone meter, one of Ophir’s direct-to-PC interfaces could be an ideal solution. These are full-fledged Laser Power and Energy meters, but instead of having a separate on-board display, the PC becomes your display. In this video you will learn about the range of PC Interfaces available from Ophir.

The Ophir Quasar is a Bluetooth interface that enables you to connect a laser sensor to a PC, or to an Android smartphone or tablet, without cables.
In this short video, you’ll learn what it can do and how to get started using it.

Tutorials and Articles

QUASAR Laser power measurement through the air

One of the inconveniences in the measurement of laser power and energy is what to do with the cables connecting the display to the sensor. These cables are of a limited flexibility and they clutter the workspace where the measurement is to be done. Sometimes, due to their stiffness, a motion of the cable moves the sensors and misaligns the set up.

 阅读更多...

Yield Improvement by Online Measurement and Analysis of Laser Energy Using Ophir’s Quasar

The Quasar wireless Bluetooth laser power and energy measurement interface allows quick and trouble free installation of complex measurement systems in an existing manufacturing environment, with a minimum of cable laying and disturbance to the facility’s operations.

This was demonstrated in a project undertaken recently, and is a typical example of what of multi-user systems see in the field.

 阅读更多...

Since introducing the first mobile phone power meter app we have been getting a lot of questions about it. Here are some of the more frequent ones:

Accessories

Customers that purchase the above items also consider the following items. Ophir-Spiricon meters and sensors include a standard manufacturers warranty for one year. Add a one year Extended Warranty to your meter or sensor, which includes one recalibration.
  • USB to Bluetooth adapter

    USB to Bluetooth adapter

    7E10039

    Adapter for PC or Laptop not equipped with built in Bluetooth. This adapter is tested and recommended by Ophir. Quasar is not guaranteed to work with all other adapters on the market.

  • Replacement battery pack

    Replacement battery pack for Nova II and Vega

    7E14007

    Replacement battery pack

  • N Polarity Power Supply/Charger

    Power Supply/Charger for Vega, Nova II, Laserstar, Nova, EA-1, Pulsar, Quasar, 6K-W, 120K-W and fan cooled sensors (1 unit supplied with these products)