| Item |
Specification |
| Camera |
SP503U |
SP620U |
USB L11058 |
| Application: |
format, slim profile, wide dynamic range, CW & pulsed lasers, adjustable ROI |
1/1.8" format, high resolution, wide
dynamic range, pulsed lasers, CW
YAG, adjustable ROI |
36mm x 24mm, 35mm format for large
beams, CW YAG, Adjustable ROI |
| Spectral Response: |
190 - 1320nm(2) |
190 - 1320nm(2) |
190 - 1100nm(2) |
| Maximum beam size: |
6.3mm W x 4.7mm H |
7.1mm W x 5.4mm H |
20mm W x 13.5mm H |
| Pixel spacing: |
9.9µm x 9.9µm |
4.40µm x 4.40µm |
9.0µm x 9.0µm |
| Number of effective pixels: |
640 x 480 |
1600 x 1200 |
4008 x 2672 |
| Minimum system dynamic range: |
64 dB |
62 dB |
59dB |
| Linearity with Power: |
±1% |
±1% |
±1% |
| Accuracy of beam width: |
±2% |
| Frame rates:
In 12 bit mode: |
50 fps at full resolution
80 fps at 320x240 |
7.5 fps at full resolution
28 fps at 640x480 |
3.1 fps at full resolution
higher rates with binning and smaller
region of interest |
| Shutter duration: |
30us to multiple frame times |
10us to multiple frame times |
| Gain control |
43:1 automatic or manual control |
29:1 automatic or manual control |
14:1 manual control LBA only |
| Trigger: |
Various options below allow synchronization with laser pulses at up to 1KHz repetition rates(4). LED on camera indicates triggering. Built in pre-trigger allows synchronization to even sub-nanosecond pulses. The various trigger input options are given below:
- Built in optical trigger on camera face unique to Spiricon SP cameras. Will synchronize with laser pulse energies >10µJ under most conditions(5).
- BNC connector accepts positive or negative voltage trigger. Same connector can provide trigger out to synch laser. Supports programmable delay on Strobe Out.
- Optional external photodiode trigger connects to cable and BNC input of camera for cases where optical signal does not reach built in optical trigger - see below.
|
Supports both Trigger In and Strobe
Out. |
| Photodiode trigger: |
Optional photodiode trigger available: P/N SPZ17005 |
N/A |
| Saturation intensity 1: |
1.3µW/cm2 2.2µW/cm2 |
2.2µW/cm2 |
0.15µW/cm2 |
| Lowest measurable signal 1: |
0.5nW/cm2 |
2.5nW/cm2 |
0.17nW/cm2 |
| Damage threshold: |
50W/cm2 / 0.1J/cm2 with all filters installed for <100ns pulse width(3) |
0.15mW/cm2 |
| Dimensions and CCD recess: |
96mm x 76mm x 16mm
CCD recess: 4.5mm below surface |
96mm x 76mm x 23mm
CCD recess: 4.5mm below surface |
83mm x 76mm x 128mm
CCD recess: 18.8mm below bezel,
31.75 from ND filter holder |
| Image quality at 1064nm: |
Pulsed with trigger synch -
excellent
Pulsed with video trigger - good
CW - poor |
Pulsed with trigger synch - excellent
Pulsed with video trigger - good CW
- good |
Pulsed with trigger synch- excellent
Pulsed with video trigger - good CW
- good |
| Operation mode: |
Interline transfer progressive scan CCD |
| Software supported: |
BeamGage, LBA and BeamStar |
BeamGage and LBA |
| PC interface: |
USB 2.0 |
| Minimum host system requirements: |
Pentium IV 1GHz (Dual-core & >2GHz for best performance), 1GB Memory, USB2, Operating system: Windows XP
Pro, Vista-32 |
English
日本語
中文
Deutsch
русский
USB CCD-Kameras
Print
Version
